Wpisy

,

Raspberry Pi-like RK3568 SBC vs Raspberry Pi Compute Module 4 based devices

Radxa, in collaboration with Rockchip’s Toybrick division, began sampling the new community-supported SBC built around Rockchip RK3568 with NPU. ROCK 3A is basically a little brother of ROCK Pi 4, with some improvements from the experience on ROCK Pi 4, the main features are:

  • RK3568 based, Quad A55 up to 2GHz, Mali G52 GPU, 0.8T NPU
  • pluggable eMMC module, 2/4/8GB LPDDR4 3200MT/s, dram controller frequency up to 1560MHz
  • QC/PD power support, with a new generation QC/PD protocol IC
  • Two USB2 same as ROCK Pi 4, two USB3(1x OTG+1x HOST), the two USB3 can be configured in SATA mode with a SATA breakout cable
  • GbE with PoE support
  • M.2 M key for NVMe with PCIe 3.0 x2 lanes
  • M.2 E key for connectivity with PCIe 2.0 x1/SDIO/UART, support WiFi 6 cards
  • 1x MIPI DSI, 1x MIPI CSI, compatible with ROCK Pi 4
  • 40P GPIO mostly compatible with ROCK Pi 4

Source: https://forum.radxa.com/t/new-rock-3a-brought-to-you-by-radxa-and-rockchip/6800

Radxa ROCK 3A
Radxa ROCK 3A

ROCK 3A will run Debian 10, maintained by the Toybrick team. Other community distributions will also be supported too. Early samples(few) for developers are ready. A larger batch will be available in late August 2021. As for an alternative, Raspberry Pi Compute Module 4 based devices are ready for orders.

ModBerry 500 CM4 an ultimate solution for IoT monitoring

TECHBASE’s ModBerry industrial computer series has received an update to Compute Module 4 and is available for orders. TECHBASE is leading manufacturer of Industrial Raspberry Pi and Industrial Compute Module solutions. ModBerry 500 series is fully compatible with all releases of Compute Module from Rasbperry Pi foundation.

ModBerry 500 CM4, First industrial computer based on Raspberry Pi’s Compute Module 4

Main features of updated device are:

  • up to 4x faster eMMC Flash with up to 32GB storage
  • up to 2x faster performance of CPU appllications than previous CM3 version
  • up to 8x more RAM (8GB LPDDR4-3200)
  • 1Gbit Ethernet interface
  • PCI 2.0 card support for NVMe SSD drive (via M.2)
  • two PCIe support for wireless modem solutions, i.e. LTE/5G modems
Order ModBerry 500 CM4 NOW!

Raspberry Pi Compute Module 4 world premiere

Few days ago, Raspberry Foundation announced new member of its family, a Rasbperry Pi Compute Module 4. It’s quite obvious, even from the first look, that the new module is very different from its predecessors. Main difference is a new form factor, leaving DDR2 SODIMM in the past.

The same 64-bit quad-core BCM2711 application processor as in Raspberry Pi 4B, the Compute Module 4 brings higher performance: faster CPU cores, better multimedia, more interfacing capabilities, and, for the first time, a choice of RAM densities and a wireless Wi-Fi and Bluetooth connectivity options.

Compute Module 4 comes in 32 variants. Lite, as always, offers no eMMC memory, a and standard versions come with up to 8GB RAM, 32 eMMC Flash and wireless modem.

New Raspberry Pi Compute Module 4 in new form factor

New features of Compute Module 4

  • 1.5GHz quad-core 64-bit ARM Cortex-A72 CPU as in Raspberry Pi 4 version B
  • 1GB, 2GB, 4GB or 8GB LPDDR4-3200 SDRAM
  • 8GB, 16GB or 32GB eMMC Flash storage for Standard version, Lite version without eMMC
  • Optional 2.4GHz and 5GHz IEEE 802.11b/g/n/ac wireless LAN and Bluetooth 5.0
  • Single-lane PCI Express 2.0 interface
  • Gigabit Ethernet PHY with IEEE 1588 support
  • Dual HDMI interfaces, at resolutions up to 4K
  • 28 GPIO pins, with up to 6 × UART, 6 × I2C and 5 × SPI

Source: https://www.raspberrypi.org/blog/raspberry-pi-compute-module-4/

/0 Komentarze/Autor
,

World-first industrial AI Gateway for Machine Learning Industrial IoT

New features of Edge TPU brought to ModBerry series

In October 2020, with the release of the latest Compute Module 4 from Rasbperry Pi Foundation, TECHBASE announced an upgraded device from ModBerry 500 series, called ModBerry 500 CM4. Thanks to the high-performance PCI-Express bus introduced in Compute Module 4 and Raspberry Pi community, the device itself presents support for a wide range of new applications, such as use of Google’s Artificial Intelligence modules at ease.

Therefore, TECHBASE designed a new device, called ModBerry AI GATEWAY 9500-CM4, utilizing the vertical format of ModBerry 9500, latest Compute Module 4 and Google’s Coral TPU. Installation-ready AI GATEWAY allows direct application in industrial fields.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with Coral TPU enhancement 

Neuron network capabilities enhance CM4-based devices, not only collecting and sending data, but also allows local data change predictions and allows direct management on-site. This feature gives the possibility for various applications, such as data analysing and establishing trends predictions, smart alarms and smart monitoring, local notification control, etc.

Used Edge TPU coprocessor via PCI-Express bus is capable of performing 4 trillion operations per second (TOPS), using 0.5 watts for each TOPS (2 TOPS per watt). Google Coral easily integrates with Raspberry Pi Compute Module in Linux and optionally in Windows with full support of TensorFlow Lite framework and AutoML Vision Edge solution.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU
TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with available expansion cards 

ModBerry AI GATEWAY 9500-CM4 can be equipped with serial RS-232/485 ports, range of digital and analog I/Os, USB, HDMI and Ethernet. Interfaces can be expanded with additional I/Os and opto-isolation, relays, Ethernet, 1-Wire, CAN, M-Bus Master and Slave, accelerometer, OLED screen and many more features like TPM Security Chip, eSIM and SuperCap backup power support. 

ModBerry AI GATEWAY 9500-CM4 series also offers a standard PCI module support for various wireless communication protocols, such as:

  • GSM modem (4G/LTE and fast 5G modem, interchangeable with Coral TPU)
  • economic NarrowBand-IoT technology
  • LoRa, ZigBee, Sigfox, Wireless M-Bus
  • secondary Wi-Fi/Bluetooth interface or Wi-Fi Hi-Power
  • custom wireless interfaces

ModBerry AI GATEWAY 9500-CM4 availabilityFirst prototypes are being developed, since Compute Module 4 is already available for the purchase. Delivery time for various configurations of AI GATEWAY will be approximately 2 months, depending on the CM4 supply on the market and chosen expansion cards. For more information contact TECHBASE’s Sales Department via email or Live Chat here.

Pre-order ModBerry AI GATEWAY 9500-CM4 NOW!
/0 Komentarze/Autor
,

World-first industrial AI Gateway for IoT Machine Learning

New features of Edge TPU brought to ModBerry series

In October 2020, with the release of the latest Compute Module 4 from Rasbperry Pi Foundation, TECHBASE announced an upgraded device from ModBerry 500 series, called ModBerry 500 CM4. Thanks to the high-performance PCI-Express bus introduced in Compute Module 4 and Raspberry Pi community, the device itself presents support for a wide range of new applications, such as use of Google’s Artificial Intelligence modules at ease.

Therefore, TECHBASE designed a new device, called ModBerry AI GATEWAY 9500-CM4, utilizing the vertical format of ModBerry 9500, latest Compute Module 4 and Google’s Coral TPU. Installation-ready AI GATEWAY allows direct application in industrial fields.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with Coral TPU enhancement 

Neuron network capabilities enhance CM4-based devices, not only collecting and sending data, but also allows local data change predictions and allows direct management on-site. This feature gives the possibility for various applications, such as data analysing and establishing trends predictions, smart alarms and smart monitoring, local notification control, etc.

Used Edge TPU coprocessor via PCI-Express bus is capable of performing 4 trillion operations per second (TOPS), using 0.5 watts for each TOPS (2 TOPS per watt). Google Coral easily integrates with Raspberry Pi Compute Module in Linux and optionally in Windows with full support of TensorFlow Lite framework and AutoML Vision Edge solution.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU
TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with available expansion cards 

ModBerry AI GATEWAY 9500-CM4 can be equipped with serial RS-232/485 ports, range of digital and analog I/Os, USB, HDMI and Ethernet. Interfaces can be expanded with additional I/Os and opto-isolation, relays, Ethernet, 1-Wire, CAN, M-Bus Master and Slave, accelerometer, OLED screen and many more features like TPM Security Chip, eSIM and SuperCap backup power support. 

ModBerry AI GATEWAY 9500-CM4 series also offers a standard PCI module support for various wireless communication protocols, such as:

  • GSM modem (4G/LTE and fast 5G modem, interchangeable with Coral TPU)
  • economic NarrowBand-IoT technology
  • LoRa, ZigBee, Sigfox, Wireless M-Bus
  • secondary Wi-Fi/Bluetooth interface or Wi-Fi Hi-Power
  • custom wireless interfaces

ModBerry AI GATEWAY 9500-CM4 availabilityFirst prototypes are being developed, since Compute Module 4 is already available for the purchase. Delivery time for various configurations of AI GATEWAY will be approximately 2 months, depending on the CM4 supply on the market and chosen expansion cards. For more information contact TECHBASE’s Sales Department via email or Live Chat here.

Pre-order ModBerry AI GATEWAY 9500-CM4 NOW!
/0 Komentarze/Autor
,

Developer from Google updates Coral Dev Board AI module

Important update for the Dev Board / SoM

If you have a Coral Dev Board or Coral SoM, please install latest Mendel update as soon as possible to receive a critical fix to part of the SoC power configuration. To get it, just log onto your board and install the update as follows:

Dev Board / Som

This will install a patch from NXP for the Dev Board / SoM’s SoC, without which it’s possible the SoC will overstress and the lifetime of the device could be reduced. If you recently flashed your board with the latest system image, you might already have this fix (we also updated the flashable image today), but it never hurts to fetch all updates, as shown above.

Source: https://developers.googleblog.com/2021/06/developer-updates-from-coral.html

WebCoral – Coral USB accelerator for Chrome browser

If you don’t like typing the command line in the terminal, Google has added Coral USB Accelerator support in Chrome over WebUSB. Only works on Linux and macOS for now. You’ll need to set up a web server and enter some commands to set up device rules on Linux, but when you’re done, go to http: // localhost: 8000 in Chrome and flash your USB accelerator software. Try some models, such as SSD MobileNet v2, with your own images.

Edge TPU

New features of Edge TPU brought to ModBerry series

In October 2020, with the release of the latest Compute Module 4 from Rasbperry Pi Foundation, TECHBASE announced an upgraded device from ModBerry 500 series, called ModBerry 500 CM4. Thanks to the high-performance PCI-Express bus introduced in Compute Module 4 and Raspberry Pi community, the device itself presents support for a wide range of new applications, such as use of Google’s Artificial Intelligence modules at ease.

Therefore, TECHBASE designed a new device, called ModBerry AI GATEWAY 9500-CM4, utilizing the vertical format of ModBerry 9500, latest Compute Module 4 and Google’s Coral TPU. Installation-ready AI GATEWAY allows direct application in industrial fields.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with Coral TPU enhancement 

Neuron network capabilities enhance CM4-based devices, not only collecting and sending data, but also allows local data change predictions and allows direct management on-site. This feature gives the possibility for various applications, such as data analysing and establishing trends predictions, smart alarms and smart monitoring, local notification control, etc.

Used Edge TPU coprocessor via PCI-Express bus is capable of performing 4 trillion operations per second (TOPS), using 0.5 watts for each TOPS (2 TOPS per watt). Google Coral easily integrates with Raspberry Pi Compute Module in Linux and optionally in Windows with full support of TensorFlow Lite framework and AutoML Vision Edge solution.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU
TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with available expansion cards 

ModBerry AI GATEWAY 9500-CM4 can be equipped with serial RS-232/485 ports, range of digital and analog I/Os, USB, HDMI and Ethernet. Interfaces can be expanded with additional I/Os and opto-isolation, relays, Ethernet, 1-Wire, CAN, M-Bus Master and Slave, accelerometer, OLED screen and many more features like TPM Security Chip, eSIM and SuperCap backup power support. 

ModBerry AI GATEWAY 9500-CM4 series also offers a standard PCI module support for various wireless communication protocols, such as:

  • GSM modem (4G/LTE and fast 5G modem, interchangeable with Coral TPU)
  • economic NarrowBand-IoT technology
  • LoRa, ZigBee, Sigfox, Wireless M-Bus
  • secondary Wi-Fi/Bluetooth interface or Wi-Fi Hi-Power
  • custom wireless interfaces

ModBerry AI GATEWAY 9500-CM4 availabilityFirst prototypes are being developed, since Compute Module 4 is already available for the purchase. Delivery time for various configurations of AI GATEWAY will be approximately 2 months, depending on the CM4 supply on the market and chosen expansion cards. For more information contact TECHBASE’s Sales Department via email or Live Chat here.

Pre-order ModBerry AI GATEWAY 9500-CM4 NOW!
/0 Komentarze/Autor
,

ZigBee Mesh technology used in end-point IoT devices

ZigBee Mesh used in end-point IoT devices

ZigBee mesh’s usefulness for IoT is partly due to the fact that it is an open standard. The same products can be used all over the world, which gives customers a large selection of available option. The high competition between products and producers means that the created solutions are innovative, characterized by high quality and give customers a considerable choice. Many suppliers of cooperating elements of this ecosystem mean that they are not limited to any specific brands or specific semiconductor manufacturers.

ZigBee Mesh. Source: ZigBee Alliance
ZigBee Mesh. Source: ZigBee Alliance

Compatibility is also promoted, as ZigBee Mesh 3.0 brings all the various ZigBee environments to a single, unified standard. Over the years, ZigBee has covered applications ranging from industrial to business to home, which has led to the development of separate service standards. ZigBee 3.0 collects all these various applications under one umbrella. This eliminates the need for mediation bridges between different sets of ZigBee supporting devices. All of them will be able to communicate directly, regardless of type.

Competitiveness of ZigBee based solutions

With a maximum data bandwidth of 250 kbps at 2.4 GHz, ZigBee is slower than other popular wireless standards such as Wi-Fi or Bluetooth, but it doesn’t matter in typical sensor applications. ZigBee Mesh is designed to send small data packets at relatively long intervals, which is usually sufficient to collect data from temperature sensors, safety sensors, air quality monitoring systems and similar subsystems. In the meantime, the low bandwidth affects the low power needed for the system to work, so that ZigBee nodes can usually work for many years on a single AAA battery.

ZigBee Power Consumption. Source: ZigBee Alliance
ZigBee Power Consumption. Source: ZigBee Alliance

With low power consumption, ZigBee supporting products typically have a short transmission range – typically from 10 to 15 meters, and the signal they emit is easily disturbed by obstacles on the route, or changes in the environment. However, the beauty of ZigBee devices lies in their work as part of a lattice topology network, where each of them transmits signals between themselves over a total of longer distances. The grid topology also means that damage to a single device will not stop the entire network, as communication can simply be redirected.

Data security via ZigBee wireless technology

ZigBee 3.0 has introduced an advanced set of tools that allows designers to introduce reliable networks with a balanced security policy and ease of installation. Available features will be constantly updated to respond to emerging threats. The security solution used is based on the ZigBee PRO grating protocol, which was originally created for the ZigBee Smart Energy profile. It is currently used by hundreds of millions of media consumption meters around the world, without detecting any security holes.

New features include device-unique authentication, when connecting to the mesh network, updating of keys used during work, secure software update via wireless network and data encryption at the logical layer of the link.

Industrial use of ZigBee Mesh

One of industrial IoT devices, supporting ZigBee Mesh technology is eModGATE from TECHBASE. Economical, ESP32-based solution can serve as an end-point in any installation or works well as a gateway, gathering data from scattered sensor mesh across the installation. For more information check Industrial IoT Shop with all the configuration options for eModGATE, including ZigBee modem.

Check eModGATE options
/0 Komentarze/Autor
,

World-first industrial AI Gateway for Machine Learning IoT

New features of Edge TPU brought to ModBerry series

In October 2020, with the release of the latest Compute Module 4 from Rasbperry Pi Foundation, TECHBASE announced an upgraded device from ModBerry 500 series, called ModBerry 500 CM4. Thanks to the high-performance PCI-Express bus introduced in Compute Module 4 and Raspberry Pi community, the device itself presents support for a wide range of new applications, such as use of Google’s Artificial Intelligence modules at ease.

Therefore, TECHBASE designed a new device, called ModBerry AI GATEWAY 9500-CM4, utilizing the vertical format of ModBerry 9500, latest Compute Module 4 and Google’s Coral TPU. Installation-ready AI GATEWAY allows direct application in industrial fields.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with Coral TPU enhancement 

Neuron network capabilities enhance CM4-based devices, not only collecting and sending data, but also allows local data change predictions and allows direct management on-site. This feature gives the possibility for various applications, such as data analysing and establishing trends predictions, smart alarms and smart monitoring, local notification control, etc.

Used Edge TPU coprocessor via PCI-Express bus is capable of performing 4 trillion operations per second (TOPS), using 0.5 watts for each TOPS (2 TOPS per watt). Google Coral easily integrates with Raspberry Pi Compute Module in Linux and optionally in Windows with full support of TensorFlow Lite framework and AutoML Vision Edge solution.

TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU
TECHBASE’s AI GATEWAY series, world-first industrial gateway utilizing Raspberry Pi Compute Module 4 and Google Coral TPU

AI GATEWAY with available expansion cards 

ModBerry AI GATEWAY 9500-CM4 can be equipped with serial RS-232/485 ports, range of digital and analog I/Os, USB, HDMI and Ethernet. Interfaces can be expanded with additional I/Os and opto-isolation, relays, Ethernet, 1-Wire, CAN, M-Bus Master and Slave, accelerometer, OLED screen and many more features like TPM Security Chip, eSIM and SuperCap backup power support. 

ModBerry AI GATEWAY 9500-CM4 series also offers a standard PCI module support for various wireless communication protocols, such as:

  • GSM modem (4G/LTE and fast 5G modem, interchangeable with Coral TPU)
  • economic NarrowBand-IoT technology
  • LoRa, ZigBee, Sigfox, Wireless M-Bus
  • secondary Wi-Fi/Bluetooth interface or Wi-Fi Hi-Power
  • custom wireless interfaces

ModBerry AI GATEWAY 9500-CM4 availabilityFirst prototypes are being developed, since Compute Module 4 is already available for the purchase. Delivery time for various configurations of AI GATEWAY will be approximately 2 months, depending on the CM4 supply on the market and chosen expansion cards. For more information contact TECHBASE’s Sales Department via email or Live Chat here.

Pre-order ModBerry AI GATEWAY 9500-CM4 NOW!
/0 Komentarze/Autor
,

Balena IoT platform for Raspberry Pi CM4 based devices

The balena platform provides a variety of tools to build, deploy, and manage IoT applications on your device. This IoT development platform is designed for use with Linux-based devices such as Raspberry Pi and Nvidia’s Jetson TX2. The device is initially flashed on balena OS with Docker compatible container and Yocto Linux based host operating system. Therefore, you are free to choose your own development framework, but you also have to code the functionality yourself.

Key Features for Balena IoT Platform :

  • Linux containers for Single Board Computers (SBCs).
  • Support for open-source tools such as balenaOS, balenaEngine, and balenaEtcher.
  • Built on Git, Docker, and Yocto.
  • A device supervisor container to continue running and pulling new code even if an application crashes.
  • Communication between balena and the device goes through encryption at all times.

Source: https://www.cnx-software.com/2021/08/06/iot-development-platform-comparision-toit-balena-particle-microsoft-azure-iot/

ModBerry 500 CM4 an ultimate solution for IoT monitoring

TECHBASE’s ModBerry industrial computer series has received an update to Compute Module 4 and is available for orders. TECHBASE is leading manufacturer of Industrial Raspberry Pi and Industrial Compute Module solutions. ModBerry 500 series is fully compatible with all releases of Compute Module from Rasbperry Pi foundation.

ModBerry 500 CM4, First industrial computer based on Raspberry Pi’s Compute Module 4

Main features of updated device are:

  • up to 4x faster eMMC Flash with up to 32GB storage
  • up to 2x faster performance of CPU appllications than previous CM3 version
  • up to 8x more RAM (8GB LPDDR4-3200)
  • 1Gbit Ethernet interface
  • PCI 2.0 card support for NVMe SSD drive (via M.2)
  • two PCIe support for wireless modem solutions, i.e. LTE/5G modems
Order ModBerry 500 CM4 NOW!

Raspberry Pi Compute Module 4 world premiere

Few days ago, Raspberry Foundation announced new member of its family, a Rasbperry Pi Compute Module 4. It’s quite obvious, even from the first look, that the new module is very different from its predecessors. Main difference is a new form factor, leaving DDR2 SODIMM in the past.

The same 64-bit quad-core BCM2711 application processor as in Raspberry Pi 4B, the Compute Module 4 brings higher performance: faster CPU cores, better multimedia, more interfacing capabilities, and, for the first time, a choice of RAM densities and a wireless Wi-Fi and Bluetooth connectivity options.

Compute Module 4 comes in 32 variants. Lite, as always, offers no eMMC memory, a and standard versions come with up to 8GB RAM, 32 eMMC Flash and wireless modem.

New Raspberry Pi Compute Module 4 in new form factor

New features of Compute Module 4

  • 1.5GHz quad-core 64-bit ARM Cortex-A72 CPU as in Raspberry Pi 4 version B
  • 1GB, 2GB, 4GB or 8GB LPDDR4-3200 SDRAM
  • 8GB, 16GB or 32GB eMMC Flash storage for Standard version, Lite version without eMMC
  • Optional 2.4GHz and 5GHz IEEE 802.11b/g/n/ac wireless LAN and Bluetooth 5.0
  • Single-lane PCI Express 2.0 interface
  • Gigabit Ethernet PHY with IEEE 1588 support
  • Dual HDMI interfaces, at resolutions up to 4K
  • 28 GPIO pins, with up to 6 × UART, 6 × I2C and 5 × SPI

Source: https://www.raspberrypi.org/blog/raspberry-pi-compute-module-4/

/0 Komentarze/Autor
,

MinCab the smallest Raspberry Pi CM4 carrier board

MinCab could be a good replacement for the upcoming (and delayed) Raspberry Pi 4 Model A for anyone who wants to use the Broadcom BCM2711 processor in a more compact form factor, but to be honest, like Piunora. You can’t save space compared to a standard carrier board. This is because there are multiple ports at the cost of thickening the system.

Uptime Lab does not have any information about the carrier board on its website at this time.  It’s similar in concept, although admittedly much smaller (when the CM4 is not connected), to the open-source hardware Less-is-More (LiM) carrier board that also offers a USB-C port for power and two LED’s, as well as a MicroSD card slot for the latest version.

Source: https://www.cnx-software.com/2021/08/10/mincab-smallest-raspberry-pi-cm4-carrier-board/

ModBerry 500 CM4 an ultimate solution for IoT monitoring

TECHBASE’s ModBerry industrial computer series has received an update to Compute Module 4 and is available for orders. TECHBASE is leading manufacturer of Industrial Raspberry Pi and Industrial Compute Module solutions. ModBerry 500 series is fully compatible with all releases of Compute Module from Rasbperry Pi foundation.

ModBerry 500 CM4, First industrial computer based on Raspberry Pi’s Compute Module 4

Main features of updated device are:

  • up to 4x faster eMMC Flash with up to 32GB storage
  • up to 2x faster performance of CPU appllications than previous CM3 version
  • up to 8x more RAM (8GB LPDDR4-3200)
  • 1Gbit Ethernet interface
  • PCI 2.0 card support for NVMe SSD drive (via M.2)
  • two PCIe support for wireless modem solutions, i.e. LTE/5G modems
Order ModBerry 500 CM4 NOW!

Raspberry Pi Compute Module 4 world premiere

Few days ago, Raspberry Foundation announced new member of its family, a Rasbperry Pi Compute Module 4. It’s quite obvious, even from the first look, that the new module is very different from its predecessors. Main difference is a new form factor, leaving DDR2 SODIMM in the past.

The same 64-bit quad-core BCM2711 application processor as in Raspberry Pi 4B, the Compute Module 4 brings higher performance: faster CPU cores, better multimedia, more interfacing capabilities, and, for the first time, a choice of RAM densities and a wireless Wi-Fi and Bluetooth connectivity options.

Compute Module 4 comes in 32 variants. Lite, as always, offers no eMMC memory, a and standard versions come with up to 8GB RAM, 32 eMMC Flash and wireless modem.

New Raspberry Pi Compute Module 4 in new form factor

New features of Compute Module 4

  • 1.5GHz quad-core 64-bit ARM Cortex-A72 CPU as in Raspberry Pi 4 version B
  • 1GB, 2GB, 4GB or 8GB LPDDR4-3200 SDRAM
  • 8GB, 16GB or 32GB eMMC Flash storage for Standard version, Lite version without eMMC
  • Optional 2.4GHz and 5GHz IEEE 802.11b/g/n/ac wireless LAN and Bluetooth 5.0
  • Single-lane PCI Express 2.0 interface
  • Gigabit Ethernet PHY with IEEE 1588 support
  • Dual HDMI interfaces, at resolutions up to 4K
  • 28 GPIO pins, with up to 6 × UART, 6 × I2C and 5 × SPI

Source: https://www.raspberrypi.org/blog/raspberry-pi-compute-module-4/

/0 Komentarze/Autor
,

Raspberry Pi-like RK3568 SBC vs Raspberry Pi Compute Module 4 based devices

Radxa, in collaboration with Rockchip’s Toybrick division, began sampling the new community-supported SBC built around Rockchip RK3568 with NPU. ROCK 3A is basically a little brother of ROCK Pi 4, with some improvements from the experience on ROCK Pi 4, the main features are:

  • RK3568 based, Quad A55 up to 2GHz, Mali G52 GPU, 0.8T NPU
  • pluggable eMMC module, 2/4/8GB LPDDR4 3200MT/s, dram controller frequency up to 1560MHz
  • QC/PD power support, with a new generation QC/PD protocol IC
  • Two USB2 same as ROCK Pi 4, two USB3(1x OTG+1x HOST), the two USB3 can be configured in SATA mode with a SATA breakout cable
  • GbE with PoE support
  • M.2 M key for NVMe with PCIe 3.0 x2 lanes
  • M.2 E key for connectivity with PCIe 2.0 x1/SDIO/UART, support WiFi 6 cards
  • 1x MIPI DSI, 1x MIPI CSI, compatible with ROCK Pi 4
  • 40P GPIO mostly compatible with ROCK Pi 4

Source: https://forum.radxa.com/t/new-rock-3a-brought-to-you-by-radxa-and-rockchip/6800

Radxa ROCK 3A
Radxa ROCK 3A

ROCK 3A will run Debian 10, maintained by the Toybrick team. Other community distributions will also be supported too. Early samples(few) for developers are ready. A larger batch will be available in late August 2021. As for an alternative, Raspberry Pi Compute Module 4 based devices are ready for orders.

ModBerry 500 CM4 an ultimate solution for IoT monitoring

TECHBASE’s ModBerry industrial computer series has received an update to Compute Module 4 and is available for orders. TECHBASE is leading manufacturer of Industrial Raspberry Pi and Industrial Compute Module solutions. ModBerry 500 series is fully compatible with all releases of Compute Module from Rasbperry Pi foundation.

ModBerry 500 CM4, First industrial computer based on Raspberry Pi’s Compute Module 4

Main features of updated device are:

  • up to 4x faster eMMC Flash with up to 32GB storage
  • up to 2x faster performance of CPU appllications than previous CM3 version
  • up to 8x more RAM (8GB LPDDR4-3200)
  • 1Gbit Ethernet interface
  • PCI 2.0 card support for NVMe SSD drive (via M.2)
  • two PCIe support for wireless modem solutions, i.e. LTE/5G modems
Order ModBerry 500 CM4 NOW!

Raspberry Pi Compute Module 4 world premiere

Few days ago, Raspberry Foundation announced new member of its family, a Rasbperry Pi Compute Module 4. It’s quite obvious, even from the first look, that the new module is very different from its predecessors. Main difference is a new form factor, leaving DDR2 SODIMM in the past.

The same 64-bit quad-core BCM2711 application processor as in Raspberry Pi 4B, the Compute Module 4 brings higher performance: faster CPU cores, better multimedia, more interfacing capabilities, and, for the first time, a choice of RAM densities and a wireless Wi-Fi and Bluetooth connectivity options.

Compute Module 4 comes in 32 variants. Lite, as always, offers no eMMC memory, a and standard versions come with up to 8GB RAM, 32 eMMC Flash and wireless modem.

New Raspberry Pi Compute Module 4 in new form factor

New features of Compute Module 4

  • 1.5GHz quad-core 64-bit ARM Cortex-A72 CPU as in Raspberry Pi 4 version B
  • 1GB, 2GB, 4GB or 8GB LPDDR4-3200 SDRAM
  • 8GB, 16GB or 32GB eMMC Flash storage for Standard version, Lite version without eMMC
  • Optional 2.4GHz and 5GHz IEEE 802.11b/g/n/ac wireless LAN and Bluetooth 5.0
  • Single-lane PCI Express 2.0 interface
  • Gigabit Ethernet PHY with IEEE 1588 support
  • Dual HDMI interfaces, at resolutions up to 4K
  • 28 GPIO pins, with up to 6 × UART, 6 × I2C and 5 × SPI

Source: https://www.raspberrypi.org/blog/raspberry-pi-compute-module-4/

/0 Komentarze/Autor
,

CarPiHat – a new interface for Raspberry Pi 4 to support IVMS

A new PCB to help interface a Raspberry Pi 4 to your car has come to the market. CarPiHat is a Raspberry Pi Car Interface, changing the power supply voltage to support the Raspberry Pi and add a range of I/Os to the board.

The board conforms to the standard HAT format, including EEPROM for automatic configuration of some device tree overlays. All connections are made with Molex’s heavy-duty, snap-on Molex nanofit connector. The board has the following features:

  • 12V – 5V buck converter to power the Pi and touchscreen, with fuse and filtering.
  • Safe shutdown circuitry to allow the Pi to control its own power.
  • < 1mA current draw when switched off.
  • Dedicated reverse, illumination and aux inputs, all opto isolated.
  • 2 opto isolated general purpose inputs. (for a total of 5 inputs)
  • 2 high current, high side switched 12V outputs (@1A). (for switching relays, lights etc)
  • 1 independent CAN bus port.
  • Real time clock to maintain system time across reboots.
  • Broken out I2C bus.
  • Broken out 1W for temperature sensor etc.
  • Mounting hardware (4 standoffs and 8 machine screws)
  • 5V Power Output for display etc.

Source: https://www.tindie.com/products/tjd/carpihat-raspberry-pi-car-interface-pcb/

Sleep functionality for ModBerry 500 CM4 devices

TECHBASE company designed an extended version of Raspberry Pi Compute Module 4 based devices, ModBerry 500-CM4-PM series for better power management in changing conditions of industrial applications. With the use of GPIO the module can manage boot, sleep mode or safe shutdown of the device in terms of unexpected drop in the power network with help of built-in ESP32 module and Arduino environment.

In the last few years developers marketed a wide range of ARM-based development boards, lacking in enhanced power management, especially sleep and wake up modes, commonly used in PC-grade computing. These boards are not adjusted for battery power supply, so it’s natural that sleep/wake functions should be implemented. In connection with the development of solutions based on Linux-SBC, key factor is adding sleep modes to any remote installation

ESP32 based addon module for Raspberry Pi

With built-in algorithms and the possibility to program on your own, the TECHBASE’s sleep/wake addon module can wake the device using a scheduler/timer. The module itself is based on ESP32-WROVER, used in the Moduino X series. ESP32 as a lightweight and low-powered solution is a perfect aid system for Raspberry Pi. Another option is wake on external triggers, e.g. change of input state, etc. All the options for sleep, shutdown and wake can be configured for various scenarios to ensure constant operation of devices, safety of data and continuity of work in case of power failure in any installation.

Sleep mode with additional power backup

Additional power management option for ModBerry devices is sleep functionality enhanced with SuperCap UPS energy backup device. This solution allows programming scenarios including the execution of chosen actions, in order to save data, send a notification and restart/shutdown the controller after completion.

Advanced power management solution

Most advanced configuration includes use of ESP32 module, known from the successful, lightweight Moduino X series, for extra logic for wake up / sleep scripts. This addon will allow the RaspberryPi-based ModBerry device to be woken up by the internal ESP32 controller. 

Moduino-ModBerry symbiosis allows a wide range of wake-up/sleep schedule customization, in order to perform best and save energy according to power supply state. Arduino and MicroPython environments provide libraries to control different scenarios of data and power management.

ModBerry 500-CM4-PM availability

The preliminary ModBerry 500-CM4-PM devices are available on request and delivery time will be specified by the Sales Dept. depending on the size of the project. Contact via email or Live Chat here: https://iiot-shop.com/product/modberry-500-cm4-pm/

/0 Komentarze/Autor